返回首页
当前位置: 主页 > 航空资料 > 机务资料 >

A320飞机维护手册 AMM WINGS 机翼3(158)

时间:2011-03-27 12:43来源:蓝天飞行翻译 作者:航空 点击:
  

 (4)
 Make sure that the access platform is in position below the applicable No. 4 flap track beam (1), zone 587 (687).


 **ON A/C 301-399,
 Subtask 57-51-33-860-053-A
 B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 (1)
 Make sure that the fairings of the applicable No.4 flap track have been removed (Ref. TASK 57-55-11-000-004).

 (2)
 Make sure that the carriage has been removed from the applicable No.4 flap track beam (Ref. TASK 27-54-46-000-001).

 (3)
 Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) is installed on the flap/slat control lever.

 (4)
 Make sure that the access platform is in position below the applicable No. 4 flap track beam (1), zone 587 (687).

 


 **ON A/C ALL
 Subtask 57-51-33-865-058
 C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
 4. Procedure
_________
 **ON A/C 301-399,
 (Ref. Fig. 402/TASK 57-51-33-991-002-A)
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 (Ref. Fig. 404/TASK 57-51-33-991-004)
 **ON A/C ALL
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
 EDGE:

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.


 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.


R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 Subtask 57-51-33-560-052
 A. Preparation of a Replacement Component WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
 (1)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 (2)
 Apply a layer of SEALANTS (Material No. 09-001) to the shims (12).

 (3)
 Put all the shims (12) and the bearing pads (11) in position.

 (4)
 Install the bolts (9) and the nuts (13).

 (5)
 Install the studs (8), the washers (14) and the nuts (15).

 (6)
 TORQUE the nuts (15) to between 2.26 and 2.40 m.daN (16.66 and 17.69 lbf.ft).

 (7)
 Install the new cotter pins (16).


R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-51-33Page 480 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1


R  **ON A/C 301-399, 
R  Subtask 57-51-33-560-052-A 
R  A. Preparation of a Replacement Component 
R  WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL_______ 
R  MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. 
R  OBEY THE MANUFACTURERS INSTRUCTIONS. 
R  PUT ON PROTECTIVE CLOTHING. 
R  DO NOT GET THEM IN YOUR MOUTH. 
R  DO NOT SMOKE. 
R  DO NOT BREATHE THE GAS. 
R  THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. 
R  GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED. 
R  (1) Make sure that the parts retained from the removed component are 
R  clean and in the correct condition. 
R  (2) Apply a layer of SEALANTS (Material No. 09-001) to the shims (12). 
R  (3) Put the set of shims (12) and the bearing pads (11) in the positions 
R  that they were removed from (do one side at a time). 
R  (4) Install the bolts (9) and the nuts (13) 
R  (5) Install the studs (8), the washers (14) and the nuts (15). 
R  (6) TORQUE the nuts (15) to between 2.26 and 2.40 m.daN (16.66 and 17.69 
R  lbf.ft). 
R  (7) Install the new cotter pins (16). 
R  **ON A/C ALL
 Subtask 57-51-33-420-070
 B. Preparation for Installation
 (1) Clean the component interfaces and the adjacent areas with a
 
中国航空网 www.aero.cn
民航翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM WINGS 机翼3(158)
 

------分隔线----------------------------